Install a CO Detector

Edited by Robbi

Safety is a major concern in every home. Installing a carbon monoxide detector will make your worries fly away.

Estrella sacragon CO2.jpg

All products usually come with a complete instruction and installation manual. Most products are usually very easy to install, but make sure you read and follow the instructions provided within the packaging. If you still cannot successfully mount your new detector, try to follow these easy steps.

Was this helpful? Yes | No | I need help

Ad

How to Install a CO Detector

  1. 1
    Determine Location.
    Identify where to intelligently place your CO2 alarm(s). Usually and preferably they are placed near your bedroom. Some would also place it near the kitchen area, where possible leaks and sources of carbon monoxide are present.
    Advertisement
    Was this step helpful? Yes | No | I need help

  2. 2
    Mount the Alarm.
    Securely mount your alarm in the area you have chosen. Alarms are designed to be mounted as a corded unit. You may directly plug it in a socket available on your walls. If the transformer or adapter is taken out of the unit, the alarm can be mounted on the wall at an eye level for easy reference.
    Advertisement
    Was this step helpful? Yes | No | I need help

  3. 3
    Power Back-Up.
    Make sure to be ready in case of a power outage. Since the system you will have is entirely electrically dependent. You must at all times be ready with a 9V battery to back up the unit. Recommended to be used while installing the device is an Energizer 522 or a Duracell MN 1604. If you want to use one for extensive life, you may opt to go for an Ultra life lithium powered cell model U9VL. These brands of batteries are easily available in any hardware stores near you. To install your backup batteries, just open the back portion of your alarm and snap the battery connector into the battery. You will hear a sound that signals that you have successfully placed your batteries.
    Was this step helpful? Yes | No | I need help

  4. 4
    Plug it in.
    As you have done in the previous three steps, you are now ready to plug the alarm into a standard, unswitched 120 volt AC electric outlet.
    Was this step helpful? Yes | No | I need help

  5. 5
    System Check.
    You will either see a red flashing dot or three eights in the display indicating that the alarm is warming up. This means that you have successfully installed the unit. After approximately 20 seconds, the first reading will appear on the display. You must see on the display only zero (0). If not then consult your manufacturer about a defect on the item or call the customer service hotline if available.
    Was this step helpful? Yes | No | I need help

  6. 6
    Test the Unit.
    The red dot you have seen should continuously blink. Test the unit to see if it is functioning properly by pressing and releasing the "Test/Reset" button. After 15 seconds, you will hear four quick beeps followed by five seconds of silence, then followed by four quick beeps. If these are achieved, you are almost done with your setup.
    Was this step helpful? Yes | No | I need help

  7. 7
    Complete the Installation.
    After doing the six preceding steps, you are now ready to test if the unit can really wake you up with its loud alarm. Try to ask help from other members of the family or someone who can assist you. Try to test the alarm of the unit by doing step 6. While testing you should be in your sleeping area with the door closed to test if you can clearly hear the noise from the alarm. If yes, then you have successfully installed your alarm and it will now monitor for the presence of carbon monoxide in your home.
    Was this step helpful? Yes | No | I need help

    Advertisement

A safe and secure home can be yours when you make use of the right technology. Just follow these easy steps to have a home that is a safer place to live in.

Comments

VisiHow welcomes all comments. If you do not want to be anonymous, register or log in. It is free.




LadyGeek
Featured Author
94 Articles Started
2,223 Article Edits
68,130 Points
LadyGeek is a featured author with VisiHow. LadyGeek has achieved the level of "Major" with 68,130 points. LadyGeek has started 94 articles (including this one) and has also made 2,223 article edits. 426,000 people have read LadyGeek's article contributions.
LadyGeek's Message Board
LadyGeek: Hi, my name is LadyGeek.
LadyGeek: Can I help you with your problem about "Install a CO Detector, publicly known also as Co2 detector"?
 

Article Info

Categories : Safety | Home

Share this Article:

Thanks to all authors for creating a page that has been read one time.

Do you have a question not answered in this article?
Click here to ask one of the writers of this article
x

Thank Our Volunteer Authors.

Would you like to give back to the community by fixing a spelling mistake? Yes | No