Add or Remove an iPhone 6 Bumper

Edited by Grimm, Anonymous, Robert, Eng

Hi, welcome to VisiHow. Today I'm going to teach you a little bit about the iPhone 6 bumper. Specifically I'm going to show you how to install it, how to remove it, and when you should use one. In this example, we will be using an iPhone 6 (it's not an iPhone 6 plus, it's just a regular iPhone 6) and we will notice that it is really slim. It is a pleasant phone to hold, but it is a little bit slippery. The bumper case does a couple of things for the phone that a traditional thin case also does - the difference is that when the thin case is added it makes the phone thicker, which you can easily feel when you hold the phone in your hands. A bumper case leaves the phone at its original thickness. When you hold the phone without the case or with a bumper case, you can better notice the original design and appeal of the iPhone 6. If you find that you have a more traditional case and it's not working for you, that's when you want to get a bumper case. A traditional case can only go on the phone one correct way. For example, the charging port has a small covered opening that will only fit easily over the charging port. A bumper case could be mistakenly put on the incorrect way. Since the bumper doesn't cover the back of the phone like a traditional case, it is advised that we install a thin protector onto the back of the phone before installing a bumper case.

Was this helpful? Yes | No | I need help

Add or remove an iPhone 6 bumper.mp4-canvas14 938671.jpg
Ad

Steps

  1. 1
    Line up the button and port openings on the bumper case with the buttons and port openings on the phone, and slide the bumper onto the top of the phone only.
    Add or remove an iPhone 6 bumper.mp4-canvas201 446801.jpg
    Advertisement
    Was this step helpful? Yes | No | I need help

  2. 2
    Push the edge of the bumper over the buttons on the left side of the phone.
    Make sure the openings on the bumper correspond with the phone buttons.
    Add or remove an iPhone 6 bumper.mp4-canvas204 968621.jpg
    Advertisement
    Was this step helpful? Yes | No | I need help

  3. 3
    Push the edge of the bumper case over the button on the right side of the phone.
    This side has only an opening for our power button, but no opening for our SIM card, so we don't have to worry about it popping out.
    Add or remove an iPhone 6 bumper.mp4-canvas211 027574.jpg
    Was this step helpful? Yes | No | I need help

  4. 4
    Pull the bottom left corner of the bumper over the edge of the phone and make sure it is securely on the phone.
    Now, both top corners and one of the bottom corners of the bumper are secured onto the phone.
    Add or remove an iPhone 6 bumper.mp4-canvas220 862029.jpg
    Was this step helpful? Yes | No | I need help

  5. 5
    To secure the last corner of the bumper to the phone, flex the bumper so that it slightly bends and is able to secure to the phone easier.
    The reason we install it this way, is because the bottom of the bumper case has a number of holes in it, unlike the top, making the bottom of the case much more pliable and easier to manipulate onto the phone itself.
    Add or remove an iPhone 6 bumper.mp4-canvas236 726602.jpg
    Was this step helpful? Yes | No | I need help

  6. 6
    To remove the case, begin at the bottom right corner.
    I do not recommend starting the removal on the left side because it is a weaker point of the case, as you can notice the structural reinforcement on the left side.
    Add or remove an iPhone 6 bumper.mp4-canvas263 111646.jpg
    Was this step helpful? Yes | No | I need help

  7. 7
    Begin by pushing down with your thumb on the corner of the case, there is no need to use your thumbnail - only use your thumb.
    You will feel the case begin to slide off.
    Add or remove an iPhone 6 bumper.mp4-canvas270 405594.jpg
    Was this step helpful? Yes | No | I need help

  8. 8
    On the back of the phone, press your finger into the corner of the phone while pressing with your thumb to further loosen the phone from the case.
    Add or remove an iPhone 6 bumper.mp4-canvas279 50564.jpg
    Was this step helpful? Yes | No | I need help

  9. 9
    The case should easily pull off once we have the bottom right corner removed.
    Add or remove an iPhone 6 bumper.mp4-canvas285 330987.jpg
    Was this step helpful? Yes | No | I need help

  10. 10
    This bumper case adds the ability to tie cell phone charms to your phone, located at the bottom left side of the bumper case.
    If we were new to the iPhone 6, we might not have realized the rear camera slightly sticks out, and the bumper case extends past the camera and allows the phone to sit flat while lying down on a smooth surface. Without the bumper case, the camera protrudes enough to make the phone slightly crooked while lying flat. Now you know the reasons why you should add a bumper case, and the best method of putting on or taking off a bumper case on the iPhone 6. If you have any questions or comments, please enter them in the section below. Thank you for using VisiHow, have a great day.
    Was this step helpful? Yes | No | I need help

    Advertisement

Video: Add or Remove an iPhone 6 Bumper

Comments

VisiHow welcomes all comments. If you do not want to be anonymous, register or log in. It is free.




Grimm
Featured Author
811 Articles Started
3,555 Article Edits
154,415 Points
Grimm is a featured author with VisiHow. Grimm has achieved the level of "Colonel" with 154,415 points. Grimm has started 811 articles (including this one) and has also made 3,555 article edits. 2,078,000 people have read Grimm's article contributions.
Grimm's Message Board
Grimm: Hi, my name is Grimm.
Grimm: Can I help you with your problem about "Add or remove an iphone 6 bumper"?
 

Article Info

Categories : IPhone

Recent edits by: Robert, Anonymous, Grimm

Share this Article:

Thanks to all authors for creating a page that has been read 13 times.

Do you have a question not answered in this article?
Click here to ask one of the writers of this article
x

Thank Our Volunteer Authors.

Would you like to give back to the community by fixing a spelling mistake? Yes | No